THE EFFECT OF ELECTRIC FLOW ON DECORATIVE KROM ELECTROPLATING WITH COPPER BASE METAL TOWARD CORROSION RATE

Authors

  • Ahmadi Ahmadi Program Studi Pendidikan Kimia FPMIPA IKIP Mataram
  • Citra Ayu Dewi Program Studi Pendidikan Kimia FPMIPA IKIP Mataram

DOI:

https://doi.org/10.33394/j-ps.v1i2.1010

Keywords:

Electric Current, Electroplating, Decorative Chrome, Corrosion Rate

Abstract

In this study a decorative chrome electroplating process has been carried out with a copper base metal, metal electroplating is often used as a means to provide a thin layer on the surface of other metals or substrates using metal which has advantages in terms of property and corrosion resistance. In decorative chrome electroplating nickel and chrome are used as coatings, nickel and chrome are used as coatings because of their protective and decorative properties, protective means they can prevent corrosion and decorative because they look shiny so they look attractive. Copper metal is chosen because of its huge application in the community. This study aims to measure the corrosion rate in copper metal after a decorative chrome electroplating process based on electric current used during the electroplating process. This research is important because during the electroplating process a decorative chrome electoplating technique will be obtained in the form of modules, and the module will be used to train students to increase their skills. This research was conducted in the IKIP Mataram chemical laboratory with a time of one year. The process carried out in this study sequentially is to prepare an electrolyte solution used for electroplating, preparing the copper base metal to be free of oxide or rust, nickel coating and finally coating with chrome. From the coating process carried out then the results will be analyzed the corrosion rate by immersion in NaCl solution at a concentration of 36.05 grams / L for 336 hours, based on variations in electric current used during the electroplating process of 0.5; 1; 1.5; 2; and 2.5 Ampere, the corrosion rate results were 0.029; 0.013; 0.017; 0.022; and 0.012 mm / yr; while the copper metal which is not coated with a corrosion rate is 0.308 mm / yr. Thus it can be concluded that copper metal coated with nickel chrome will effectively resist the lowest rate of corrosion in the current given 2.5 Ampere.

References

Ahmadi, (2011): Studi Pelapisan Nikel-Krom Pada Baja St 37 Untuk Pembelajaran Kimia di SMA, Tesis Program Magister Pengajaran Kimia ITB, Bandung, 1.

Alian, H., (2010): Pengaruh Tegangan Pada Proses Elektroplating Baja Dengan Pelapisan Seng dan Krom Terhadap Kekerasan dan Laju Korosinya., Jurnal Teknik Mesin Universitas Sriwijaya.,245-247.

Hajati, N. L., Herbudiman, B., Hazairin., Suryanto., (2006): Kajian Pengaruh Tebal Lapisan Coating pada Laju Korosi Tulang Beton, Jurnal Teknik Sipil Institut Teknologi Nasional Bandung, 76.

Kaban, H., Niar, S., Jorena., (2010): Menguji Kekuatan Bahan Elektroplating Pelapisan Nikel pada Substrat Besi dangan Uji Impak (Impact Test), Jurnal Penelitian Sains, FMIPA Universitas Sriwijaya, Vol. 13, 27.

Kanani, N., (2006): Electroplating, Basic principles, Processes, and Practice, Elsevier, Netherland, 10.

Perez, N., (2004): Electrochemistry and Corrosion Science, Newyork, Boston, Dordrecht, London, Moskow, Kluwer Academic Publishers, 1, 80-81.

Prayitno, Dwi, (2005), Perbedaan Berat Hasil Pelapisan Nikel Akibat Penggunaan Lapisan Dasar Cu dan Tanpa Lapisan Dasar Cu Dengan Variasi Waktu Pada Bahan Baja Karbon Rendah, Skripsi Pendidikan Teknik Mesin, Uneversitas Negeri Semarang, 7.

Santosa, B., Syamsa, M., (2007) : Pengaruh Parameter Proses Pelapisan Nikel Terhadap Ketebalan Lapisan, Jurnal Teknik Mesin Uneversitas Jenderal Ahmad Yani, Bandung, 9, 26.

Suarsana, I., (2008): Pengaruh waktu pelapisan nikel pada tembaga dalam pelapisan khrom dekoratif terhadap tingkat kecerahan dan ketebalan lapisan, Jurnal Ilmiah Teknik Mesin Universitas Udayana, 2(1), 48.

Sugiono, (2008): Metode Penelitian Kualiatatif dan R & D, Alfabeta, Bandung.

Supardi, R. (1997): Korosi, Tarsito, Bandung, 1, 73.

Wahyudi, S., (2006): Buku Saku Elektroplating, Technic, Cimahi Bandung 61, 63.

Downloads

Published

2013-12-21

How to Cite

Ahmadi, A., & Dewi, C. A. (2013). THE EFFECT OF ELECTRIC FLOW ON DECORATIVE KROM ELECTROPLATING WITH COPPER BASE METAL TOWARD CORROSION RATE. Prisma Sains : Jurnal Pengkajian Ilmu Dan Pembelajaran Matematika Dan IPA IKIP Mataram, 1(2), 134–138. https://doi.org/10.33394/j-ps.v1i2.1010

Issue

Vol. 1 No. 2: December 2013

Section

Research Articles

License

Authors who publish with this journal agree to the following terms:

  1. Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License that allows others to share the work with an acknowledgement of the work's authorship and initial publication in this journal.
  2. Authors are able to enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or publish it in a book), with an acknowledgement of its initial publication in this journal.
  3. Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) prior to and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work (See The Effect of Open Access).

 Creative Commons License
This work is licensed under a Creative Commons Attribution 4.0 International License.